View 74LS197_187041.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

4-STAGE PRESETTABLE RIPPLE COUNTERS
The SN54/74LS196 decade counter is partitioned into divide-by-two and divide-by-five sections which can be combined to count either in BCD (8, 4, 2, 1) sequence or in a bi-quinary mode producing a 50% duty cycle output. The SN54/74LS197 contains divide-by-two and divide-by-eight sections which can be combined to form a modulo-16 binary counter. Low Power Schottky technology is used to achieve typical count rates of 70 MHz and power dissipation of only 80 mW. Both circuit types have a Master Reset (MR) input which overrides all other inputs and asynchronously forces all outputs LOW. A Parallel Load input (PL) overrides clocked operations and asynchronously loads the data on the Parallel Data inputs (Pn) into the flip-flops. This preset feature makes the circuits usable as programmable counters. The circuits can also be used as 4-bit latches, loading data from the Parallel Data inputs when PL is LOW and storing the data when PL is HIGH.
SN54/74LS196 SN54/74LS197
4-STAGE PRESETTABLE RIPPLE COUNTERS
LOW POWER SCHOTTKY
J SUFFIX CERAMIC CASE 632-08
14 1
* * * * * * *
Low Power Consumption -- Typically 80 mW High Counting Rates -- Typically 70 MHz Choice of Counting Modes -- BCD, Bi-Quinary, Binary Asynchronous Presettable Asynchronous Master Reset Easy Multistage Cascading Input Clamp Diodes Limit High Speed Termination Effects CONNECTION DIAGRAM DIP (TOP VIEW)
VCC 14 MR 13 Q3 12 P3 11 P1 10 Q1 9 CP0 8
NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual In-Line Package.
14 1
N SUFFIX PLASTIC CASE 646-06
14 1
D SUFFIX SOIC CASE 751A-02
ORDERING INFORMATION
SN54LSXXXJ SN74LSXXXN SN74LSXXXD Ceramic Plastic SOIC
1 PL
2 Q2
3 P2
4 P0
5 Q0
6 CP1
7 GND
PIN NAMES
LOADING (Note a) HIGH LOW 1.5 U.L. 1.75 U.L. 0.8 U.L. 0.5 U.L. 0.25 U.L. 0.25 U.L. 5 (2.5) U.L.
8 6
LOGIC SYMBOL
1 PL 4 10 3 11 P0 P1 P2 P3
CP0 CP1 (LS196) CP1 (LS197) MR PL P0-P3 Q0-Q3
Clock (Active LOW Going Edge) Input to Divide-by-Two Section Clock (Active LOW Going Edge) Input to Divide-by-Five Section Clock (Active LOW Going Edge) Input to Divide-by-Eight Section Master Reset (Active LOW) Input Parallel Load (Active LOW) Input Data Inputs Outputs (Notes b, c)
1.0 U.L. 2.0 U.L. 1.0 U.L. 1.0 U.L. 0.5 U.L. 0.5 U.L. 10 U.L.
CP0
CP1 MR 13
Q0 Q1 Q2 Q3 5 9 2 12
VCC = PIN 14 GND = PIN 7
NOTES: a. 1 TTL Unit Load (U.L.) = 40A HIGH/1.6 mA LOW. b. The Output LOW drive factor is 2.5 U.L. for Military (54) and 5 U.L. for Commercial (74) b. Temperature Ranges. c. In addition to loading shown, Q0 can also drive CP1.
FAST AND LS TTL DATA 5-372
SN54/74LS196 * SN54/74LS197
LOGIC DIAGRAM
MR PL
13
P0
4
P1
10
P2
3
P3
11
1
8
J SD Q
J SD Q
J SD Q
J SD Q
CP0
K CD Q
6
K CD Q
K CD Q
K CD Q
CP1 Q0
5
9
2
12
Q1
Q2
Q3
LS196
MR PL
13
P0
4
P1
10
P2
3
P3
11
1
8
J SD Q
J SD Q
J SD Q
J SD Q
CP0
K CD Q
6
K CD Q
K CD Q
K CD Q
CP1 Q0
5
9
2
12
Q1
Q2
Q3
LS197
VCC = PIN 14 GND = PIN 7 = PIN NUMBERS
FAST AND LS TTL DATA 5-373
SN54/74LS196 * SN54/74LS197
FUNCTIONAL DESCRIPTION The LS196 and LS197 are asynchronously presettable decade and binary ripple counters. The LS196 Decade Counter is partitioned into divide-by-two and divide-by-five sections while the LS197 is partitioned into divide-by-two and divideby-eight sections, with all sections having a separate Clock input. In the counting modes, state changes are initiated by the HIGH to LOW transition of the clock signals. State changes of the Q outputs, however, do not occur simultaneously because of the internal ripple delays. When using external logic to decode the Q outputs, designers should bear in mind that the unequal delays can lead to decoding spikes and thus a decoded signal should not be used as a clock or strobe. The CP0 input serves the Q0 flip-flop in both circuit types while the CP1 input serves the divide-by-five or divide-by-eight section. The Q0 output is designed and specified to drive the rated fan-out plus the CP1 input. With the input frequency connected to CP0 and Q0 driving CP1, the LS197 forms a straightforward module-16 counter, with Q0 the least significant output and Q3 the most significant output. The LS196 Decade Counter can be connected up to operate in two different count sequences, as indicated in the tables of Figure 2. With the input frequency connected to CP0 and with Q0 driving CP1, the circuit counts in the BCD (8, 4, 2, 1) sequence. With the input frequency connected to CP1 and Q3 driving CP0, Q0 becomes the low frequency output and has a 50% duty cycle waveform. Note that the maximum counting rate is reduced in the latter (bi-quinary) configuration because of the interstage gating delay within the divide-by-five section. The LS196 and LS197 have an asynchronous active LOW Master Reset input (MR) which overrides all other inputs and forces all outputs LOW. The counters are also asynchronously presettable. A LOW on the Parallel Load input (PL) overrides the clock inputs and loads the data from Parallel Data (P0 - P3) inputs into the flip-flops. While PL is LOW, the counters act as transparent latches and any change in the Pn inputs will be reflected in the outputs.
Figure 2. LS196 COUNT SEQUENCES
DECADE (NOTE 1) COUNT 0 1 2 3 4 5 6 7 8 9 Q3 L L L L L L L L H H Q2 L L L L H H H H L L Q1 L L H H L L H H L L Q0 L H L H L H L H L H COUNT 0 1 2 3 4 5 6 7 8 9 Q0 L L L L L H H H H H BI-QUINARY (NOTE 2) Q3 L L L L H L L L L H Q2 L L H H L L L H H L Q1 L H L H L L H L H L
NOTES: 1. Signal applied to CP0, Q0 connected to CP1. 2. Signal applied to CP1, Q3 connected to CP0.
MODE SELECT TABLE
INPUTS RESPONSE MR L H H PL X L H CP X X Reset (Clear) Parallel Load Count
H = HIGH Voltage Level L = LOW Voltage Level X = Don't Care = HIGH to Low Clock Transition
FAST AND LS TTL DATA 5-374
SN54/74LS196 * SN54/74LS197
GUARANTEED OPERATING RANGES
Symbol VCC TA IOH IOL Supply Voltage Operating Ambient Temperature Range Output Current -- High Output Current -- Low Parameter 54 74 54 74 54, 74 54 74 Min 4.5 4.75 - 55 0 Typ 5.0 5.0 25 25 Max 5.5 5.25 125 70 - 0.4 4.0 8.0 Unit V C mA mA
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage 54 Input LOW Voltage 74 Input Clamp Diode Voltage 54 Output HIGH Voltage 74 54, 74 VOL Output LOW Voltage 74 Input HIGH Current Data, PL MR, CP0 (LS196) MR, CP0, CP1 (LS197) CP1 (LS196) Data, PL MR, CP0 (LS196) MR, CP0, CP1 (LS197) CP1 (LS196) Input LOW Current Data, PL MR CP0 CP1 (LS196) CP1 (LS197) Short Circuit Current (Note 1) Power Supply Current - 20 0.35 0.5 20 40 40 80 0.1 0.2 0.2 0.4 - 0.4 - 0.8 - 2.4 - 2.8 - 1.3 - 100 27 V 2.7 3.5 0.25 0.4 V V 2.5 - 0.65 3.5 0.8 - 1.5 V V Min 2.0 0.7 V Typ Max Unit V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = - 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA IOL = 8.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table
A
VCC = MAX, VIN = 2.7 V
IIH
mA
VCC = MAX, VIN = 7.0 V
IIL
mA
VCC = MAX, VIN = 0.4 V
IOS ICC
mA mA
VCC = MAX VCC = MAX
Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.
FAST AND LS TTL DATA 5-375
SN54/74LS196 * SN54/74LS197
AC CHARACTERISTICS (TA = 25C)
Limits LS196 Symbol fMAX tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPHL Parameter Maximum Clock Frequency CP0 Input to Q0 Output CP1 Input to Q1 Output CP1 Input to Q2 Output CP1 Input to Q3 Output Data to Output PL Input to Any Output MR Input to Any Output Min 30 Typ 40 8.0 13 16 22 38 41 12 30 20 29 27 30 34 15 20 24 33 57 62 18 45 30 44 41 45 51 Max Min 30 LS197 Typ 40 8.0 14 12 23 34 42 55 63 18 29 26 30 34 15 21 19 35 51 63 78 95 27 44 39 45 51 Max Unit MHz ns ns ns ns ns ns ns Test Conditions
VCC = 5.0 V CL = 15 pF
AC SETUP REQUIREMENTS (TA = 25C)
Limits LS196 Symbol tW tW tW tW ts ts th th trec Parameter CP0 Pulse Width CP1 Pulse Width PL Pulse Width MR Pulse Width Data Input Setup Time -- HIGH Data Input Setup Time -- LOW Data Hold Time -- HIGH Data Hold Time -- LOW Recovery Time Min 20 30 20 15 10 15 10 10 30 Typ Max Min 20 30 20 15 10 15 10 10 30 LS197 Typ Max Unit ns ns ns ns ns ns ns ns ns VCC = 5.0 V Test Conditions
DEFINITIONS OF TERMS SETUP TIME (ts) -- is defined as the minimum time required for the correct logic level to be present at the logic input prior to the clock transition from HIGH to LOW in order to be recognized and transferred to the outputs. HOLD TIME (th) -- is defined as the minimum time following the clock transition from HIGH to LOW that the logic level must be maintained at the input in order to ensure continued recognition. A negative HOLD TIME indicates that the correct logic level may be released prior to the clock transition from HIGH to LOW and still be recognized. RECOVERY TIME (trec) -- is defined as the minimum time required between the end of the reset pulse and the clock transition from HIGH to LOW in order to recognize and transfer LOW Data to the Q outputs.
FAST AND LS TTL DATA 5-376
SN54/74LS196 * SN54/74LS197
AC WAVEFORMS
CP
1.3 V tW(H) tPHL tPLH
1.3 V
Q
1.3 V
1.3 V
Figure 1
Pn tPHL
1.3 V
1.3 V tPLH
Pn tW PL 1.3 V
Qn
1.3 V
tPLH
tPHL
NOTE: PL = LOW
Qn
1.3 V
Figure 2
Figure 3
Pn*
1.3 V th(H)
1.3 V th(L) ts(L) 1.3 V 1.3 V
PL OR MR
1.3 V PL
ts(H) trec
tW
CP tPHL
1.3 V Qn* Q=P Q=P
Q
1.3 V
* The shaded areas indicate when the input is permitted * to change for predictable output performance
Figure 4
Figure 5
FAST AND LS TTL DATA 5-377
Case 751A-02 D Suffix 14-Pin Plastic SO-14 -A14 8
NOTES: 1. DIMENSIONS A" AND B" ARE DATUMS AND T" IS A DATUM SURFACE. 2. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 3. 4. CONTROLLING DIMENSION: MILLIMETER. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 5. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 6. 751A 01 IS OBSOLETE, NEW STANDARD 751A 02.
-B1 7
P
7 PL
0.25 (0.010)
M
B
M
G
C
SEATING PLANE
R X 45
D 14 PL
0.25 (0.010)
M
K
T B
S
M
F
J
A
S
DIM A B C D F G J K M P R
MILLIMETERS MIN MAX
8.55 3.80 1.35 0.35 0.40 8.75 4.00 1.75 0.49 1.25
INCHES MIN MAX
0.337 0.150 0.054 0.014 0.016 0.344 0.157 0.068 0.019 0.049
1.27 BSC 0.19 0.10 0 5.80 0.25 0.25 0.25 7 6.20 0.50
0.050 BSC 0.008 0.004 0 0.229 0.010 0.009 0.009 7 0.244 0.019
Case 632-08 J Suffix 14-Pin Ceramic Dual In-Line -A14 8
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH.
-B1 7
3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIM F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. 5. 632 01 THRU 07 OBSOLETE, NEW STANDARD
C
L
632 08.
-TSEATING PLANE
K F D 14 PL
0.25 (0.010)
M
G
T A
S
N J 14 PL
M
0.25 (0.010)
M
T
B
S
DIM A B C D F G J K L M N
MILLIMETERS MIN MAX
19.05 6.23 3.94 0.39 1.40 19.94 7.11 5.08 0.50 1.65
INCHES MIN MAX
0.750 0.245 0.155 0.015 0.055 0.785 0.280 0.200 0.020 0.065
2.54 BSC 0.21 3.18 0.38 4.31
0.100 BSC 0.008 0.125 0.015 0.170
7.62 BSC 0 0.51 15 1.01
0.300 BSC 0 0.020 15 0.040
Case 646-06 N Suffix 14-Pin Plastic
NOTES: 1. LEADS WITHIN 0.13 mm (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION.
14
8
B
1 7
2.
DIMENSION L" TO CENTER OF LEADS WHEN FORMED PARALLEL.
3.
DIMENSION B" DOES NOT INCLUDE MOLD FLASH.
4. 5.
ROUNDED CORNERS OPTIONAL. 646 05 OBSOLETE, NEW STANDARD 646 06.
A F C N H G D
SEATING PLANE
NOTE 4
L
J K M
DIM A B C D F G H J K L M N
MILLIMETERS MIN MAX
18.16 6.10 3.69 0.38 1.02 19.56 6.60 4.69 0.53 1.78
INCHES MIN MAX
0.715 0.240 0.145 0.015 0.040 0.770 0.260 0.185 0.021 0.070
2.54 BSC 1.32 0.20 2.92 2.41 0.38 3.43
0.100 BSC 0.052 0.008 0.115 0.095 0.015 0.135
7.62 BSC 0 0.39 10 1.01
0.300 BSC 0 0.015 10 0.039
FAST AND LS TTL DATA 5-378
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong.
FAST AND LS TTL DATA 5-379

▲Up To Search▲

Price & Availability of 74LS197

	To Download 74LS197 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .